Datasheet 18F – Ebook download as PDF File .pdf), Text File .txt) or read book online. PDA. View Full Version: 18F Quaduature Encoder This change will be notified in a datasheet’s () future update. PIC18FI/P Microchip Technology 8-bit Microcontrollers – MCU 16KB RAM 34 I/O datasheet, inventory, & pricing.

Author: Malalabar JoJokinos
Country: Ecuador
Language: English (Spanish)
Genre: Software
Published (Last): 10 May 2004
Pages: 139
PDF File Size: 11.30 Mb
ePub File Size: 2.3 Mb
ISBN: 674-7-13423-529-3
Downloads: 85001
Price: Free* [*Free Regsitration Required]
Uploader: Brajin

This change will be adtasheet in a datasheet’s DSB. I wish I could help but I am using the 18F in a completely different manner. I will definately incorporate. Equation ‘as shown in the data sheet’ doesn’t produce the same figures for PWM resolution shown in Table Resolution is the number of bits you have to control the duty cycle. Now, if I can just find more time to play with it.

PWM Glitch on the 18F, 18F, 18F, and 18F for very low duty cycles | Microchip

Yeah this one is a nifty series PIC for sure. I never managed to get QEI module going in velocity mode.

While Bert’s statement might sound like just so much talk to some I vouch for his opinion especially if you are moving to 18F chips for the datssheet few times, I had an amazingly difficult time just getting this chip to blink the LED, owing to programmer issues, config issues. The more we pound on this and post the results, the better we can get a handle on it.



Ramps up, then down. I was wondering datashedt someone has done same thing in pic basic i. I can see that there is a dependency with the PWM resolution, but I’m not sure how to manage it. This is part of it and not complete yet. Well,it drive me crazy to know about it. It’s a great uC! This should be more than enough for me to get started. For PWM resolution use the equation below.

CCS :: View topic – Can’t setup_spi2(mode) for Pic18f ?

I can control the Freq just fine, but it makes a mess of the duty. An 18F with two pots, a switch, and the FETs with drivers. Using Darrel’s interupt routines Datasheeet managed to get motor controller for my robot working, with PID filter and all.

Copyright c Controlled Surroundings Inc. I tried according to application note but to no avail. The fact that my frequency and duty had to be changeable made it a bit more confusing for me.

Thanks for your code although its in assembly. I datzsheet, and submitted a support ticket to Microchip. I use the “Hello World” out the serial port test. I made a few attempts to begin with but could never quite figure it out so I went for my own velocity calcs newPos-oldPos.

Dafasheet switch controls if the output is pulsed DC or cycles both ways. See this post http: Basically the module is counter and two comparators. Hi, This works for me on 18F, should be the same. Now you need to know the PWM resolution to know the range of duty cycle bits. That said, there still seems to be a bit of mystery surrounding it’s use, at least to me.


Any help with the set up code would be appreciated. When the counter starts at 0 the output is set, when it “hits” the value of the first comparator the outputs is cleared and when the counter “hits” the value of the second compartor the PWM cycle starts over.

To work with the 18F Isn’t that an awesome controller? But anyhow,it’s clear enough for me to understand. Not yet at least. First is the same thing that should be first for every new pic, can you blink a led? 18g4431 gotta some problem with the PWM Period value. Great tip on counter overflow.

LowByte hserout [“D”,dec duty,”F”,dec Freq] goto Main ‘ Loop end Like I said, I’m going to have to study my own work just to understand it better, but at least it works like it is suppose to. Bruce, That’s a super start to a beginner like me.