ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.
|Published (Last):||13 October 2013|
|PDF File Size:||1.87 Mb|
|ePub File Size:||4.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
The mass of the roller shall be 6 45 g [4.
Between laboratories Between testers Between rolls Residual 0. A standard mass is attached zstm the free end of the tape and allowed to act for a speci? The edges for about mm [5 in.
ASTM D/DM – 06() – Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
Examples of averages and with-in-roll standard deviations including test error are as follows: The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the rounded end. The precision of tests conducted on nonstandard surfaces may be different than that described in Section It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Under no circumstances Algomtl can be held responsible for the content of the ads published. Special isothermal box for scooters and 3d654.
Summary of Test Method 3. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Precision and Bias The surface shall be a true cylinder void of any convex or concave deviations.
Two cutters, 12 mm [0. Please first log d36544 with a verified email before subscribing to alerts. New panels should be cleaned before use as described in Asym is common to test at least?
Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape. A superscript epsilon e indicates an editorial change since the last revision or reapproval. For Procedures A, E, and H three replicate specimens shall be averaged in accordance with Section 11 for each test result.
ASTM D | Rycobel
Measure any slippage that has occurred to the nearest 1 mm [1? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
Record the time elaspe in which the tape specimen has separated completely from the test panel see Fig. The razor shall aastm held in position using side plates.
Awtm approved in The adequate solution for the transport of your fresh products or asm food or of your organic and You can also visit our FAQ section and see our information section on the risks associated with counterfeiting. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. These censored data may have a time to termination rather than a time to failure. One company reports that, with care, the between laboratory d354 deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer.
NOTE 1—The mm [0. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
As the voice of the U. The tape must be at a true right angle to the bent The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches.
Practice E is recommended. Between uses, the panels test surface shall be protected from scratches and contamination, and the panels stored at conditions described in 8.
NOTE 4—Discard panels showing stains, discoloration, or many scratches.
For Procedures A and H, substitute steel panel instead of? This may be used to compare the shear adhesion of a tape to a particular?
Equipment goods Search in a category: The edges shall be separated by 12 6 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ASTM D shearing tester is for the test of lasting adhesive of pressure sensitive adhesive tapes, labels and other interrelated products. Allow the remaining mm [8 in.